Messages

1

Model In-Progress / Re: 1/100 Hi nu conversion VP ver

« on: May 01, 2012, 08:37:01 AM »

I thought it was just my phone but I can't see the pictures either... But what I can see looks good

2

Capitalism Corner* / Re: BMC scribers

« on: July 15, 2008, 05:19:57 PM »

Add them ups!!!! Whats keeping you?

3

Assembly/Scratchbuilding / Re: Best place to get Kotobukiya Option Parts?

« on: March 21, 2008, 06:56:07 AM »

What are you looking for?  I've got a bunch, that I just haven't gotten a chance to put up in the store...

OH MAN....You have been holding out on us! Dam you 

4

Assembly/Scratchbuilding / Re: Ball Joints

« on: March 19, 2008, 08:30:34 PM »

The Polycaps i got on my model are stretched out. I'm trying to tighten them up. I will try the aforementioned super glue trick. I was also thinking some 2 part liquid Epoxy resin might work. Its really sticky, and a thin coat might stiffen up the joint a lot. I will try this and post my results.

Listn you can always wrap your joints in plastic wrap. ( the piece that goes in the other gets wraped) Then just cut the exposed from showing with a blae.

5

Assembly/Scratchbuilding / Re: Problem with Sand the nubs

« on: March 19, 2008, 08:27:51 PM »

Or you can use the back of a hobby knife blade

6

Assembly/Scratchbuilding / Re: Scribing Plastic

« on: March 19, 2008, 08:24:59 PM »

try harbor frieght they got a set dirt cheap

7

Capitalism Corner* / Re: polycaps

« on: March 18, 2008, 05:58:42 PM »

Finally found the camera so heres the pix.

http://i47.photobucket.com/albums/f153/OTEEBZO/MISC/polycaps002.jpg
http://i47.photobucket.com/albums/f153/OTEEBZO/MISC/polycaps001.jpg

Thanks for any help.

8

Capitalism Corner* / Re: polycaps

« on: March 17, 2008, 08:55:53 PM »

Well the smallest one I have thet will work is 7mm long from end to end with 4mm outside and 3mm inside. that is smallest I can use. So I am not sure that there is one inbetween this next one. But the next one I can use is 10mm long end to end with a 6mm outside and a 5mm inside. This being the biggest I can use. Sorry no pix my girl moved camera and she sleeping so I can't wake her. I hope this is enough info. I can use anything between these measurements. Thanks for the help.

9

Capitalism Corner* / polycaps

« on: March 15, 2008, 09:20:19 PM »

Ok , so I do not have enough polycaps for a project I am working on. I need 8 of the same size, the smaller the better. I was hoping someone out there had an over stock that they would be willing to give , trade , or sell. Please contact me

10

Capitalism Corner* / Re: GARBALDY

« on: March 14, 2008, 10:47:06 PM »

I am really sorry for being misinformed but I have been gone from here for awhile so this is all news to me. The piece looks great! So when will it be ready to send out? So I can see If I make the funds to spend?

11

Capitalism Corner* / Re: GARBALDY

« on: March 13, 2008, 06:28:36 PM »

Not sure if it is just me but I did a search on the site for it so I could see a picture but there was no results except this post. Any pictures?

12

Model In-Progress / Re: Tits McGee - Galaxy Girl!!

« on: March 02, 2008, 03:43:57 PM »

I am sorry to revisit an old thread but I have been gone for awhile and was just wondering did you coat your skintone before parafilm?  ( I would think the film would pull the pastels off)And there has been no updates in a while is she done because I would like to see the rest of the updates

13

Model Help* (Check Stickies and Search First) / Re: Mix and Match Ex-S Conversion kits

« on: March 02, 2008, 02:29:46 PM »

I think you should buy both and recast them then sell them to us!!!!!

14

Painting/Priming / Re: HELP! Can any mini compressor be attach to this airbrush?

« on: February 26, 2008, 06:39:10 PM »

You can connect any airbrush you can possible find on the market to any compressor on the market. All you need is the right adapter to fit both ends. OH and make sure you have a moist trap and air regulator.

15

Model Help* (Check Stickies and Search First) / Re: Unclogging a marker tip

« on: February 08, 2008, 10:46:18 PM »

Ink should not prove a problem with cloges , but if it does use 409 cleaning spray because it works great on cleaning clogged pens, just them soak in it and your good

16

Model Help* (Check Stickies and Search First) / Re: AirBrush parts Help!

« on: February 08, 2008, 10:30:14 PM »

There are 2 different threads to hook up to your compressor.Either your iwata hose line or there is an adaptor from badger to fit. there are many sites to check out bearair.com which I have mentioned in past post also harborfrieght which I have also mentioned for cheap look alikes that will work with other airbrush parts and there is coastairbrush.com which IS THE BEST FOR iWATA NEEDS. If you do have anyother questions please feel free to ask at anytime.

17

AoZ Unlimited Competition! / Re: Titans Test Team Tetra Threat

« on: February 08, 2008, 09:40:55 PM »

Sorry to inform but the links are not working.

18

K is for Krazy Kustom Kampfer Kompetition / Re: MS-18E Kampfer ["Kanji" Custom]

« on: July 14, 2007, 05:51:17 PM »

Congrats my friend, you should be very proud you did an great  job.Please keep them coming. hehehe

19

K is for Krazy Kustom Kampfer Kompetition / Re: KKKKK Winners Results!

« on: July 14, 2007, 05:48:26 PM »

Congrats to the winners. Good job guys!!!!
The turn out showed some very nice improvements for all the modelors.
And I would like to thank all the people that offered prizes for our very friendly comp.
Good job Mike.

20

K is for Krazy Kustom Kampfer Kompetition / Re: MS-18E Kampfer ["Kanji" Custom]

« on: July 13, 2007, 05:20:05 PM »

This one gets my vote. I love your last 2 kits the attention to detail is unbelieveable.You it look so easy.