Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Artic Fox

Pages: 1 2 3 [4] 5 6
Model In-Progress / RGM-79-BD-1 GM BLITZ
« on: March 28, 2006, 02:03:28 AM »
yea, I know what you mean, I started doing gundam models back in like 98, and I'm just barely starting to remove seamlines and airbrushing

Model In-Progress / RGM-79-BD-1 GM BLITZ
« on: March 27, 2006, 11:37:46 PM »
nice concept, but a comment on your pictures, next time use the macro function on ur camera, it will focus better on exetreme closeups like models.

Model In-Progress / Low-visiblity RX-78-2 O.Y.W
« on: March 27, 2006, 09:51:05 PM »
I started work on my O.Y.W gundam, after having burnt out on my GM and Zaku for now. The Gundam is my first airbrushing job, and I used Gunship gray, I filled in what seamlines I saw, this was also another first for me. I'll post pics of the shield in a bit.

GB3: Minimal G / Intro, Rules, Questions, and General Discussion
« on: March 05, 2006, 07:12:58 PM »
based on shuttle launches, the humany body tends to grow an inch or two due to less pressure on the spine, so the body tends to stretch

GB3: Minimal G / Intro, Rules, Questions, and General Discussion
« on: March 04, 2006, 11:46:48 PM »
I was wondeirng if you might allow me to create a religion, or religions.

GB3: Minimal G / Intro, Rules, Questions, and General Discussion
« on: March 04, 2006, 03:33:46 PM »
WIll religion be a big factor?

« on: February 26, 2006, 08:06:36 PM »
a perfect kit once again Erix, keep up the awesome work. I wanna get a tachikoma

Model In-Progress / My current projects
« on: February 26, 2006, 05:47:56 PM »
I got some progress in, I shortened the snot, and sanded down the cable connectors on the face, now, I just hafta seal the seams, and smooth the snot since it's still kinda rough.

Painting/Priming / Formula 409 and Stripping Models
« on: February 23, 2006, 10:20:53 PM »
for paint stripping I use Greased Lightning Engine degreaser and cleaner. That stuff strips anything, I've stripped enamel paints, autmotive paint to a degree, and even krylon fusion, even though it left an interesting etching in the plastic, but I think that was more from the krylon. I've read that this will melt top most layer of skin, so I always wear gloves. I let most models soak for about a week, either because it's strong paint, or I'm too lazy to take it out, but all it takes is some scrubbing and voila.

oh yea, it disolves putty too.

a gallon costs like 5 bucks

Model In-Progress / My current projects
« on: February 23, 2006, 09:39:47 PM »
yea, I know that I've gotten rid of some valuable parts of the models... it's just that I appreaciate the realisticness of the original series, I just want to do something zany, or just odd, if you were to know the real me, as in hang out with me for jsut a week, you'd see what I mean, I am essiently a very odd person, and I want my Zaku to reflect that, as for the GM, I was looking at it, and I might just carve my own details into that wide open area. THank you for the feedback.

I also plan to do some work on the Zaku head.

Model In-Progress / My current projects
« on: February 23, 2006, 04:38:42 PM »
Hi everyone, just wanted to show you some in-prog pics of two of my models, MG Zaku II and MG GM.

Well, first up is the Zaku II, It's the OYW vesion, which really isn't very different from the original Zaku II, well, the most major change is that I have removed the cables from the Zaku, I just didn't like them, that, and I broke one of the rod for the head, this is the first time that I am attempting to remove seamlines, the only parts that I haven't worked the seamlines are are the legs and head. I've also puttied up the holes for the thrusters on the legs of the zaku, along with the holes for the cables to go into. Here are my pics.

And as for my GM, I replaced the lower legs with those of the GM Kai, I puttied up the chest vents, and I added the lower thrusters from the GP-01 ground type, to the GM's left hand, as vulcan guns.
here are my pics

please tell me what you think so far. Any feedback is more than welcomed.

Model Gallery / 1/144 Kotobukiya HUCKEBEIN Mk-III (My 1st commision work)
« on: February 22, 2006, 07:34:56 PM »
yea, in the second and third pics, the borders really stick out, but really beautiful work, god, I hope I get that good.

Assembly/Scratchbuilding / Kotobukiyi Mesh Pipe
« on: February 21, 2006, 09:45:22 AM »
dude, that is awesome.

Assembly/Scratchbuilding / Kotobukiyi Mesh Pipe
« on: February 20, 2006, 10:39:12 PM »
dude, that's cool, I gotta look for those cables.

Model In-Progress / Vought F4-AU1 QUANTICO Corsair 1/48 Hasegawa
« on: February 06, 2006, 11:25:15 AM »
so, are you using an Aztec Airbrush? Nice work by the way

Model Talk / Vote For Your Favorite SD Contest Entry
« on: January 30, 2006, 11:01:15 PM »
Erix, even if you don't win, I consider your guntank, one of the best

Model Talk / Vote For Your Favorite SD Contest Entry
« on: January 30, 2006, 10:20:09 PM »
Erix I am a big fan of your work, your models llok like they could come alive and step on me.... so, I'm glad that I was able to vote on your beautiful guntank. Long Live the "Last GAte"

Model In-Progress / Weird-bot
« on: January 30, 2006, 10:13:08 PM »
it reminds me of a mobile flat form Turn A

Model In-Progress / 1:9 M1A2 Abrams
« on: January 28, 2006, 10:56:27 PM »
My dad recently started work on a R/C 1:9 M1A2 Abrams tank, and right now he is currently in the middle of post shading, the tank originaly came in a flat tan color, for desert combat, but my dad decided to take it apart in order to paint it, sorry I don't have pics of the unpainted tank, but I didn't have my card reader at the time. well here the pics of the current prog

Model Talk / Group Build Suggestions
« on: January 14, 2006, 10:16:09 PM »
That's a good one too, the out-dated tech mecha, I have lots of old busted electronics,and wires. I love being a packrat

Pages: 1 2 3 [4] 5 6